Change Language :

guidefast

Economical energy supply for crane girders and indoor cranes

guidefast

Quickly assembled as a modular solution:
The guidefast guide trough is attached to the side of the crane girder. This means that there is no need to weld brackets onto crane girders, for example. Assembly times are kept very short, as the guide trough is simply hooked into the previously attached brackets and then fixed in place with the clamping blocks. The small number of different components and the fixed channel width also contribute to easy installation.

  1. Quick and easy fastening using clamping rails
  2. One-piece steel channel with 2 m standard length
  3. abrasion-resistant: glide bar for centre-fixed
  4. Gutter joints are connected via clips, so no shearing edges
  5. Clever: 2 versions of bracket with integrated strain relief
Request guidefast now
  • Save up to 80% assembly time compared to conventional guide systems
  • Fits almost any standard crane girder
  • 2 versions of bracket with integrated strain relief, for fixed installation of cable on the crane girder ± 5mm vertical tolerance of the bracket
  • For the standard tray length of 2.0 m - with or without glide bar
  • Can be used for any side-mounted application - not just on cranes
  • Easy to install thanks to prefabricated drilling patterns of the e-chain®® -mounting bracket
  • Standard material: galvanised steel. Also available in stainless steel. Material AISI 304 (AISI 304) or black powder-coated
  • Conductivity in accordance with DIN EN 61537: Standard with special connector
  • Long-term tested: Vibration, environment, strength

Components - Holder set
A - Version 01 - short holder
B - Version 02 - long bracket
C - Clamp blocks, Part No.. GF9.2.10

Ba = e-chain® outer width
Bi = e-chain® inner width
ha = e-chain® outer height
BRi = trough inner width = BRi ≥ Ba + 4

2 versions: Holder with integrated strain relief:
A - Version 01 - short holder
B - Version 02 - long holder

guidefast
guidefast

guide trough guidefast

Components - guidefast Set1st channel profile, 2 m each
2. plastic glide bar, à 2 m, optional
3rd clip, Part No.. 908.467

guidefast

guide trough

  • Standard length: 2,000mm
  • Standard material: galvanised steel
  • Each element has an opening for cable entry
  • Version with installed glide bar is also available
  • part number varies depending on size - please refer to the table below
Part numberFor e-chain®with or without glide barinner width trough BRi [mm]A [mm]B [mm]
GF91.30.025.2000 1500.025.RRR.0 | E2.21.025.RRR.0 without glide bar 42.56181
GF91.30.050.2000 1500.050.RRR.0 | E2.21.050.RRR.0without glide bar 67.561106
GF92.30.03.2000E2.26.038.RRR.0 | 2500.03.RRR.0 without glide bar 587597
GF92.30.05.2000 E2.26.057.RRR.0 | 2500.05.RRR.0 without glide bar 7775115.5
GF92.30.07.2000E2.26.077.RRR.0 | 2500.07.RRR.0 without glide bar 9775135.5
GF92.30.09.2000 2500.09.RRR.0 | E2.26.089.RRR.0 without glide bar 10975148
GF92.30.10.20002500.10.RRR.0 | E2.26.103.RRR.0 without glide bar 12375161.5
GF95.30.05.2000E2.38.050.RRR.0 | 2700.05.RRR.0 without glide bar 70105108.5
GF95.30.07.2000E2.38.075.RRR.0 | 2700.07.RRR.0 without glide bar 95105133.5
GF95.30.10.2000E2.38.100.RRR.0 | 2700.10.RRR.0 without glide bar 120105158.5
GF91.31.025.2000 1500.025.RRR.0 | E2.21.025.RRR.0 with glide bar 42.56181
GF91.31.050.2000 1500.050.RRR.0 | E2.21.050.RRR.0 with glide bar 67.5 61106
GF92.31.03.2000 E2.26.038.RRR.0 | 2500.03.RRR.0 with glide bar 587597
GF92.31.05.2000 E2.26.057.RRR.0 | 2500.05.RRR.0 with glide bar 7775115.5
GF92.31.07.2000 E2.26.077.RRR.0 | 2500.07.RRR.0 with glide bar 9775135.5
GF92.31.09.20002500.09.RRR.0 | E2.26.089.RRR.0 with glide bar 10975148
GF92.31.10.2000 2500.10.RRR.0 | E2.26.103.RRR.0 with glide bar 12375161.5
GF95.31.05.2000E2.38.050.RRR.0 | 2700.05.RRR.0 with glide bar 70105108.5
GF95.31.07.2000 E2.38.075.RRR.0 | 2700.07.RRR.0 with glide bar 95105133.5
GF95.31.10.2000 E2.38.100.RRR.0 | 2700.10.RRR.0 with glide bar 120105158.5

guidefast
guidefast Haler short

Holder short version

  • Supplied with terminal block and screw
  • Terminal block with conductivity available in accordance with DIN EN 61537: Standard
  • Fewer fastening options for fixed cables, therefore more space-saving than the long version
  • Standard support spacing: 1 holder per metre
Part number
GF9.2.12 guidefast, holder short version - clamping block standard
GF9.2.12.CD guidefast, holder short version - clamping block with conductivity
guideast

Vertically and horizontally adjustable

guidefast
guidefast Haler long

Holder long version

  • Supplied with terminal block and screw
  • Terminal block with conductivity available in accordance with DIN EN 61537: Standard
  • Extra many fastening options for permanently installed cables
  • Standard support spacing: 1 holder per metre
Part number
GF9.2.11guidefast, holder long version - clamping block standard
GF9.2.11.CD guidefast, holder long version - clamping block with conductivity
guidefast

Bracket with integrated strain relief for mounting fixed cables on the crane girder.

guidefast
guidefast

Connector

  • Ensures that two gutter sections are connected without a step
  • Is attached with a rubber mallet
  • The connector is already included when ordering the Guidefast gutter >1000 mm
Part number
908.467 guidefast, holder short version - clamping block standard
guidefast
guidefast

Quick and easy to fit - the guidefast-guide trough.

guidefast

Mounting via welding studs or screw/thread directly on the crane girder.

Consulting

I look forward to answering your questions

Dieter Reitz
Dieter Reitz+49 2203 9649 7070Write e-mail

Shipping and consultation

In person:

Monday to Friday from 7 am - 8 pm.
Saturdays from 8 am- 12 pm.


Online:
24h

WhatsApp-Service:
Montag – Freitag: 8 – 16 Uhr